Solid Carbide End Mill Multi-Cut “Duplex”
2614AT
Article number 2614AT.016 | EAN 4037753681930
-
Unit of measurement: metricwith round, fine chip breakerRadius to be programmed in CAMRecommended feed directions of the respective cuttersRecommended ramping angle
Carbide end mill Multi-Cut Duplex in long design and with SAFE-LOCK™ system for high-performance roughing in almost all materials.
Product features and benefits:
The duplex geometry combines HPC and HFC geometry and enables 2D and 3D machining with only one tool.Very low cutting forces and reduced vibrations due to variable pitch and NR cutting edge profile.Well suited for roughing with unstable conditions.
International Material Comparison- cutting diameter Ød₁ [mm]:
- 16 mm
- cutting tolerance:
- h11
- radius r₁ [mm]:
- 7.8 mm
- radius r₂:
- 1.6 mm
- programmed radius R₃D:
- 2.2 mm
- radius deviation tmax:
- 0.5 mm
- programmed radius R₃D measuring point lₘ:
- 4.64 mm
- cutting length l₂ [mm]:
- 32 mm
- neck length l₃ [mm]:
- 40 mm
- overall length l₁:
- 92 mm
- neck diameter Ød₃:
- 15.5 mm
- shank diameter Ød₂ [mm]:
- 16 mm
- shank diameter tolerance:
- h6
- number of flutes Z:
- 4
- cutting material:
- carbide
- category:
- End Mill, High Feed Cutter
- version:
- Corner Radius (Duplex)
- product line:
- FRANKEN Multi-Cut
- tool interface:
- straight shank with pull-out protection (Safe-Lock)
- coating:
- TIALN
- internal coolant supply:
- ICA
- helix angle:
- 45 deg
Technical details
- cutting diameter Ød₁ [mm]:
- 16 mm
- cutting tolerance:
- h11
- radius r₁ [mm]:
- 7.8 mm
- radius r₂:
- 1.6 mm
- programmed radius R₃D:
- 2.2 mm
- radius deviation tmax:
- 0.5 mm
- programmed radius R₃D measuring point lₘ:
- 4.64 mm
- cutting length l₂ [mm]:
- 32 mm
- neck length l₃ [mm]:
- 40 mm
- overall length l₁:
- 92 mm
- neck diameter Ød₃:
- 15.5 mm
- shank diameter Ød₂ [mm]:
- 16 mm
- shank diameter tolerance:
- h6
- number of flutes Z:
- 4
- cutting material:
- carbide
- category:
- End Mill, High Feed Cutter
- version:
- Corner Radius (Duplex)
- product line:
- FRANKEN Multi-Cut
- tool interface:
- straight shank with pull-out protection (Safe-Lock)
- coating:
- TIALN
- internal coolant supply:
- ICA
- helix angle:
- 45 deg
cutting diameter Ød₁ [mm]
16 mm
cutting tolerance
h11
radius r₁ [mm]
7.8 mm
radius r₂
1.6 mm
programmed radius R₃D
2.2 mm
radius deviation tmax
0.5 mm
programmed radius R₃D measuring point lₘ
4.64 mm
cutting length l₂ [mm]
32 mm
neck length l₃ [mm]
40 mm
overall length l₁
92 mm
neck diameter Ød₃
15.5 mm
shank diameter Ød₂ [mm]
16 mm
shank diameter tolerance
h6
number of flutes Z
4
cutting material
carbide
category
End Mill, High Feed Cutter
version
Corner Radius (Duplex)
product line
FRANKEN Multi-Cut
tool interface
straight shank with pull-out protection (Safe-Lock)
coating
TIALN
internal coolant supply
ICA
helix angle
45 deg
Cutting value calculator
Calculator result
The cutting data shown are approximate values
which must be adapted to the conditions of use.
which must be adapted to the conditions of use.