Milling Technology - End mill cutters

354 suitable variants
Inch unit system: inch
Reset all filters
    • Finishing end mill without chip breaker for almost all materials.
      Corner protection chamfer (bevelled edge) for stabilization of the edge
      Recommended feed directions of the respective cutters
      The specific angle of 3° to 5° is the recommended angle for ramping applications

    TOP-Cut carbide end mill in long design for roughing and finishing in almost all materials.

    cutting material:
    HM
    category:
    End Mill
    version:
    Flat Face (Bevelled Edge)
    tool interface:
    straight shank
    tool interface norm:
    DIN 6535
    coating:
    TIALN
    internal coolant supply:
    without internal cooling
    helix angle:
    34-38 deg
    • Roughing end mill with round and fine knuckle form profile.
      Corner protection chamfer (bevelled edge) for stabilization of the edge
      Recommended feed directions of the respective cutters
      The specific angle of 3° to 5° is the recommended angle for ramping applications

    Multi-Cut carbide end mill in long design, with lateral driving flat and short flute length for high-performance roughing in many materials.

    cutting material:
    HM
    category:
    End Mill
    version:
    Flat Face (Bevelled Edge)
    tool interface:
    straight shank with side-lock clamping flat
    tool interface norm:
    DIN 6535
    coating:
    TIALN
    internal coolant supply:
    without internal cooling
    helix angle:
    45 deg
    • Finishing end mill without chip breaker for hardened materials.
      Corner protection chamfer (bevelled edge) for stabilization of the edge
      Recommended feed directions of the respective cutters

    Hard-Cut carbide end mill in extra long design for finishing in high-strength materials up to 66 HRC.

    cutting material:
    HM
    category:
    End Mill
    version:
    Flat Face (Bevelled Edge)
    tool interface:
    straight shank
    tool interface norm:
    DIN 6535
    coating:
    TIALN
    internal coolant supply:
    without internal cooling
    helix angle:
    50 deg
    • Finishing end mill without chip breaker for hardened materials.
      High precision corner radius for 3D-operations
      Recommended feed directions of the respective cutters
      The specific angle of 3° to 5° is the recommended angle for ramping applications

    Hard-Cut carbide torus end mill for finishing applications in many materials, including hard materials.

    cutting material:
    HM
    category:
    Torus End Mill
    tool interface:
    straight shank
    tool interface norm:
    DIN 6535
    coating:
    TIALN
    internal coolant supply:
    without internal cooling
    helix angle:
    0 deg
    • Finishing end mill without chip breaker for almost all materials.
      High precision corner radius for 3D-operations
      Recommended feed directions of the respective cutters

    TOP-Cut carbide torus end mill in extra long design for roughing and finishing applications in many materials.

    cutting material:
    HM
    category:
    Torus End Mill
    tool interface:
    straight shank
    tool interface norm:
    DIN 6535
    coating:
    TIALN
    internal coolant supply:
    without internal cooling
    helix angle:
    30 deg
    • Finishing end mill without chip breaker for almost all materials.
      Corner protection chamfer (bevelled edge) for stabilization of the edge
      Recommended feed directions of the respective cutters
      The specific angle of 3° to 5° is the recommended angle for ramping applications

    PCD torus end mill in extra long design for roughing and finishing of aluminium alloys, composite materials or graphite.

    cutting material:
    PKD
    category:
    End Mill
    version:
    Flat Face (Bevelled Edge)
    tool interface:
    straight shank
    tool interface norm:
    DIN 6535
    coating:
    without coating
    internal coolant supply:
    ICA
    helix angle:
    2,5 deg
    • Finishing end mill without chip breaker for hardened materials.
      Corner protection chamfer (bevelled edge) for stabilization of the edge
      Recommended feed directions of the respective cutters
      The specific angle of 1° to 2° is the recommended angle for ramping applications

    CBN end mill for HSC finishing of hard materials up to 66 HRC and cast materials.

    cutting material:
    CBN
    category:
    End Mill
    version:
    Flat Face (Bevelled Edge)
    tool interface:
    straight shank
    tool interface norm:
    DIN 6535
    coating:
    without coating
    internal coolant supply:
    without internal cooling
    helix angle:
    2,5 deg
    • Roughing end mill with round and coarse knuckle form profile for soft materials.
      Corner protection chamfer (bevelled edge) for stabilization of the edge
      Recommended feed directions of the respective cutters
      The specific angle of 3° to 5° is the recommended angle for ramping applications

    Alu-Cut carbide end mill in long design for roughing in wrought aluminium alloys and copper alloys.

    cutting material:
    HM
    category:
    End Mill
    version:
    Flat Face (Bevelled Edge)
    tool interface:
    straight shank
    tool interface norm:
    DIN 6535
    coating:
    CRN
    internal coolant supply:
    ICRA
    helix angle:
    40 deg
    • Roughing end mill with round and fine knuckle form profile.
      Corner protection chamfer (bevelled edge) for stabilization of the edge
      Recommended feed directions of the respective cutters
      The specific angle of 3° to 5° is the recommended angle for ramping applications

    Multi-Cut carbide end mill in long design and with lateral driving flat for high-performance roughing in many materials.

    cutting material:
    HM
    category:
    End Mill
    version:
    Flat Face (Bevelled Edge)
    tool interface:
    straight shank with side-lock clamping flat
    tool interface norm:
    DIN 6535
    coating:
    TIALN
    internal coolant supply:
    without internal cooling
    helix angle:
    45 deg
    • Roughing end mill with round and fine knuckle form profile.
      Corner protection chamfer (bevelled edge) for stabilization of the edge
      Recommended feed directions of the respective cutters
      The specific angle of 3° to 5° is the recommended angle for ramping applications

    Multi-Cut carbide end mill in extra long design, with lateral driving flat and short flute length for high-performance roughing in many materials.

    cutting material:
    HM
    category:
    End Mill
    version:
    Flat Face (Bevelled Edge)
    tool interface:
    straight shank with side-lock clamping flat
    tool interface norm:
    DIN 6535
    coating:
    TIALN
    internal coolant supply:
    without internal cooling
    helix angle:
    45 deg