GF-Z-R15-IKZ-HA-TiCN

solid carbide thread milling cutters for internal threads

Article number GF165966.9512

Machining of internal threads.

Product features and benefits:

Short machining time due to more flutes.
Deep thread possible thanks to long thread part.
Smooth milling operation thanks to flutes with 15° helix angle.
Predrilled tap hole necessary.
Pitch-dependent.
Cross-dimensional.
For internal threads the diameter of the end mill should be smaller than 2/3 or 3/4 of the thread diameter.

International Material Comparison

Details

Downloads

Technical details

Cutting Values

Cutting value calculator

Please select a material group and fill in all fields with the respective values!

Material	Steel materials Search for value P1.1 Cold-extrusion steels, Construction steels, Free-cutting steels, etc. <= 600 N/mm² P2.1 Construction steels, Cementation steels, Steel castings, etc. <= 800 N/mm² P3.1 Cementation steels, Heat-treatable steels, Cold work steels, etc. <= 1000 N/mm² P4.1 Heat-treatable steels, Cold work steels, Nitriding steels, etc. <= 1200 N/mm² P5.1 High-alloyed steels, Cold work steels, Hot work steels, etc. <= 1400 N/mm² No results found Stainless steel materials Search for value M1.1 Ferritic, martensitic <= 950 N/mm² M2.1 Austenitic <= 950 N/mm² M3.1 Austenitic-ferritic (Duplex) <= 1100 N/mm² M4.1 Austenitic-ferritic heat-resistant (Super Duplex) <= 1250 N/mm² No results found Cast materials Search for value K1.1 Cast iron with lamellar graphite (GJL) 100-250 N/mm² K1.2 Cast iron with lamellar graphite (GJL) 250-450 N/mm² K2.1 Cast iron with nodular graphite (GJS) 350-500 N/mm² K2.2 Cast iron with nodular graphite (GJS) 500-900 N/mm² K3.1 Cast iron with vermicular graphite (GJV) 300-400 N/mm² K3.2 Cast iron with vermicular graphite (GJV) 400-500 N/mm² K4.1 Malleable cast iron (GTMW, GTMB) 250-500 N/mm² K4.2 Malleable cast iron (GTMW, GTMB) 500-800 N/mm² No results found Non ferrous materials Search for value N1.1 Aluminium wrought alloys <= 200 N/mm² N1.2 Aluminium wrought alloys <= 350 N/mm² N1.3 Aluminium wrought alloys <= 550 N/mm² N1.4 Aluminium cast alloys Si <= 7% N1.5 Aluminium cast alloys 7% < Si <= 12% N1.6 Aluminium cast alloys 12% < Si <= 17% N2.1 Pure copper, low-alloyed copper <= 400 N/mm² N2.2 Copper-zinc alloys (brass, long-chipping) <= 550 N/mm² N2.3 Copper-zinc alloys (brass, short-chipping) <= 550 N/mm² N2.4 Copper-aluminium alloys (alu bronze, long-chipping) <= 800 N/mm² N2.5 Copper-tin alloys (tin bronze, long-chipping) <= 700 N/mm² N2.6 Copper-tin alloys (tin bronze, short-chipping) <= 400 N/mm² N2.7 Special copper alloys <= 600 N/mm² N2.8 Special copper alloys <= 1400 N/mm² N3.1 Magnesium wrought alloys <= 500 N/mm² N3.2 Magnesium wrought alloys <= 500 N/mm² N4.1 Duroplastics (short-chipping) N4.2 Thermoplastics (long-chipping) N4.3 Fibre-reinforced synthetics (fibre content <= 30%) N4.4 Fibre-reinforced synthetics (fibre content > 30%) N5.1 Graphite N5.2 Tungsten-copper alloys N5.3 Composite materials No results found Special materials Search for value S1.1 Pure titanium <= 450 N/mm² S1.2 Titanium alloys <= 900 N/mm² S1.3 Titanium alloys <= 1250 N/mm² S2.1 Pure nickel <= 600 N/mm² S2.2 Nickel-base alloys <= 1000 N/mm² S2.3 Nickel-base alloys <= 1600 N/mm² S2.4 Cobalt-base alloys <= 1000 N/mm² S2.5 Cobalt-base alloys <= 1600 N/mm² S2.6 Iron-base alloys <= 1500 N/mm² No results found Hard materials Search for value H1.1 High strength steels, hardened steels, hard castings 44 – 50 HRC H1.2 High strength steels, hardened steels, hard castings 50 – 55 HRC No results found

Unit	Millimeter Inch

Calculator result

The cutting data shown are approximate values
which must be adapted to the conditions of use.